GC Fuji 7 Capsule Shade - Pink

Features
Self-bonding ion exchange and high fluoride release create a strong, acid-resistant, chemically fused layer that will continue to offer protection to the occlusal surface for up to 24 months.
Etching, bonding agents, or tooth isolation is not required.
Strong, lasting bond to tooth structure.
Moisture-friendly; perfect for sealing and protecting newly erupted molars or endodontically treated preparations.
The tooth-like coefficient of thermal expansion improves the sealant staying power, which helps maintain marginal integrity (when used as a restorative).
Prevents further erosion in rampant caries cases.
Fluoride release can be recharged when the patient uses a fluoridated rinse or dentifrice. 
Mixes in 10 seconds; ideal consistency every time.
The capsule applier allows direct delivery for easy application.
Low viscosity - Penetrates into pits and fissures; it can be brushed on with a micro-tip brush or blown in with air syringe.

Description
GC Fuji VII in capsule form is the revolutionary glass ionomer sealant and surface protectant. It is fantastic at keeping young patients' teeth cavity-free. There is no isolation or bonding agent required. It works in a moist field. The self-bonding, high fluoride releasing GC Fuji VII creates a strong, acid-resistant fused layer.
Fuji VII White is for fully erupted teeth; Fuji VII Pink offers a visual indicator that is ideal for newly erupted molars. GC Fuji VII sets in around four minutes. If a faster set is desired, use a visible light curing device for 20-40 seconds. Place light source as closely as possible to the cement surface. This function applies only to the Pink Shade.
 
Indications :-

Surface and fissure protection.
Root surface protection.
Hypersensitivity prevention and control.
Intermediate endodontic sealing.
Intermediate restorations.
Caries stabilisation.

Advantages :-

Flowable consistency to ensure effective wetting and intimate adhesion to tooth surfaces
Moisture tolerant- can be applied in situations where saliva control is difficult
Available in white and special pink shades for clear identification

Key Specifications

Powder/Liquid Ratio (g/g) - 0.30/0.15.
Mixing time - 10?.
Net Volume (ml) - 0.15.
Working Time - 1?40?? .
Setting Time - Without Light Irradiation (2?30??), With Light Irradiation (20?-40?).
Compressive strength (Mpa) - After 1 Hour (100), After 1 Day (159 ), After 7 Days (171 ).
 Radiopacity (mm) - 2.4.
 Fluoride Release microgram/cm2 (After 1 Day) - 197.

Packaging

Box of 50 Capsules

Direction to Use

Shake the capsule or tap its side on a hard surface to loosen the powder.
To activate the capsule, push the plunger until it is flush with main body.
Immediately place the capsule into a metal GC Capsule Applier and click. the lever once.The capsule is now activated. Note : The capsule should be activated just before mixing and used immediately.
Immediately remove the capsule and set it into a mixer (an amalgamator) and mix for 10 seconds at high speed (4,000 RPM). 
Immediately remove the mixed capsule from the mixer and load it into the GC Capsule Applier.
Make two clicks to prime the capsule then syringe.
Remove surface moisture but do not desiccate.
Extrude cement directly into preparation, then use a brush to spread a film of GC Fuji VII directly over the root surface or hypersensitive area or over the occlusal surface and into the pits and fissures. 
A ball burnisher is used to contour the unset glass ionomer. The burnisher can be lubricated with Cocoa Butter or Fuji COAT to aid manipulation.
Form the contour and place a matrix if required.
Light-cure for 20 seconds using a suitable visible light curing device (470 nm wavelength). Light curing function only applies for pink shade. After light cure, it is advisable to protect the surface with a varnish.
Finish under water spray using superfine diamond bur, silicone point and polishing strips.