GC Gold Label 1 Capsule Box Of 30

Features
Bonds in a Wet Field

No primer or adhesive is required
Simple cementation technique

Sustained Fluoride Release

Cariostatic activity

Smooth, Creamy Consistency

Easy to mix and handle

Low Film Thickness

Restorations' seat is better; has fewer problems

Strong Direct Bond

Non-precious and precious metal to tooth structure

Superior Marginal Seal

Minimizes microleakage
Coefficient of thermal expansion is similar to tooth structure

Low Solubility After Set (.06%)

Reduced microleakage
Less chance of washouts and sensitivity developing
Faster "Snap Set" with more working time

Strong Bonding, Compressive and Tensile Strengths

Greater longevity and restoration integrity

Description


Radiopaque Glass Ionomer Luting Cement in Capsule
 Chemically cured strontium based glass ionomer cement ideal for basic luting of metal based restorations in the convenient capsule delivery.

Composition

polybasic carboxylic acid**-10-20%

Indications

Cementation of metal-based inlays, onlays, crowns, bridges and posts
Cementation of high strength (zirconia based) all ceramic crowns and bridges



Key Specifications
TECHNICAL DATA:

Powder / Liquid ratio (g/g) :0.33/0.18
Mixing time (sec.):10 secs
Working time (min., sec.) (at 23  C) (from start of mixing):2 mins 15secs
Final finishing commencing time (after seating the restoration):4 mins 30 secs

CONTRAINDICATIONS

Pulp capping
In rare cases the product may cause sensitivity in some people. If any such reactions are experienced, discontinue the use of the product and refer to a physician.

STORAGE
Recommended for optimal performance, store in a cool and dark place (4-25 C) (39.2-77.0 F).
Shelf life : 3 years from date of manufacture

Packaging
Gc Fuji 1 Capsule Box Of 50:

Box of 50 Capsules

Gc Fuji 1 Capsule Box Of 30:

Box of 30 Capsules
Direction to Use
1. TOOTH PREPARATION
a) Prepare tooth in usual manner. For pulp capping, use calcium hydroxide
b) Clean the prepared teeth with pumice and water
c) Rinse thoroughly with water. Remove excess moisture by blotting with a cotton pellet or gently blowing with an oil-free air
DO NOT DESICCATE. Prepared surfaces should appear moist (glistening)
2. RESTORATION PREPARATION
Make sure that the restoration is pretreated and handled according to the manufacturer?s instructions
3. CAPSULE ACTIVATION AND MIXING
a) Before activation, shake the capsule or tap its side on a hard surface to loosen the powder
b) To activate the capsule push the plunger until it is flush with the main body
c) Immediately place the capsule into a GC CAPSULE APPLIER and click the lever once
The capsule is now activated
Note : The capsule should be activated just before mixing and used immediately
d) Immediately remove the capsule and set it into a mixer (or an amalgamator) and mix for 10 seconds (4,000 RPM)
Note: When using a rotational mixing device, it is recommended not to use the centrifuge option
4. DISPENSING
a) Immediately remove the mixed capsule from the mixer and load it into the GC CAPSULE APPLIER
b) Make two clicks to prime the capsule
To adjust the direction of the nozzle, hold the applier with the capsule towards you and turn the capsule body
c) Extrude directly into the restoration
d) To remove the used capsule, push the applier release button. Twist the capsule and pull upwards
5. CEMENTATION
a) Coat the internal surface of the restoration with sufficient cement and seat immediately. The working time is 2 minutes 15 seconds from start of mixing at 23 C (73.4 F). Higher temperatures will shorten working time
b) Maintain moderate pressure
c) Start removing excess cement when the excess cement feels rubbery. d) Finishing can be started 4 minutes 30 seconds after seating the restoration.